One of the Radio Activites I have really enjoyed over the last few years is the Oceania DX Contest –  where the world points their antenna’s to Oceania and we are the wanted stations.

I have chosen to enter a category of SingleOp All band (160-80-40-20-15-10) SSB QRP.

My first entry was in 2016, and it was basically on a bit of a whim, and I made a handful of contacts, submitted a log and to my surprise  actually came 1-3-3  (Country-Continent-World) with a score of 2660 Yes, First in VK, 3rd in Oceania and 3rd in the world.

This motivated me somewhat to actually put in more of an effort for 2017, and in 2017, my score was 30% higher than the winning score from 2016.  Fast forward a few month’s and my results were  1-2-2  with a score of 10,368.  Yes I had achieved 1 aim of improving my score and this time moved up to 2nd in the world.  The conditions in 2017 were nowhere near as good as the previous year either.

Fast forward to early August (2018) when the 2017 Results were published, and it prompted me again to see what I could do to again further improve my score.

It came down to the 1 thing that I could change – and that is to work really hard on Antenna’s – and that is what I did.

First off, I spent some to time to come to terms learning and understanding how to use 4nec2 to model antennas and started off with the basics – model a simple dipole (Inverted-V) antenna and use it as a baseline to validate  that the model was about what I was seeing in the real world – and yeah, close enough to not get too hung up about things.

Secondly, I modeled the Antenna’s I had used for the 2017 OCDX and this alone was a real eye-opener – and actually really surprised me as to how much of a disadvantage I had put myself at!

My Antenna choices for 2017 were.

• Titan Challenger 80-10 Vertical
• End-fed “random” wire of about 57M long and 8M high with a couple of counterpoise wires
• inverted V on 40 (and also used on 15m)
• 20m 1/4 WL vertical with elevated feedpoint and radials

The Titan vertical is an awesome RX antenna – but pretty useless for TX – so was hardly used for TX.  The Inverted V – yep NVIS only on 40M and the 20M Vertical was OK.

As I had  done my base learning and modelling of the 40M inverted V, I knew the pattern is all up – so not a DX antenna at all, so I went ahead and modeled my longwire across the 3 bands I used it on.

Once I had entered all the data, it was time to run some modelling across the 3 bands that I used this antenna on – and this is where things really sunk in!

At first glance for a simple Antenna on 160M this looked OK, not all the signal was straight up, but then the I noticed the gain – Ouch – -4.9dBi – I was literally taking my 5W of RF and throwing most of it away and effectively using on about 1.5W!

The 80M pattern was not really a lot better – Again, only 0.6dBi gain  – and the main lobe was pointing in totally the wrong direction for for me to actually use!  with the 90 being North, most of my power was being sent right into the Southern Ocean where there is literally Nobody!

The 40M pattern again was not brilliant – whilst a slight gain of 5dBi when looking at the pattern, it was mostly in the wrong direction again!  where I needed it – there was a nice deep null  where I really needed a signal and probably why in hindsight that I relied on the 40M Inverted V for most of my 40M contacts.

The Challenge

Now, with an insight of how bad the antennas utilized actually were, I needed to look at modelling some better Antenna’s – and the beauty of modelling, is the try before build – which means fitting Antenna’s into the available space I had.  the second Challenge was to do all this and actually build all the required antenna’s within a fairly short period.

40M – (my favourite band)  – I wanted a decent Antenna on 40M as this is a band that I love operating on.  Whilst the dream is a 4-Square array  and yes, I’m fortunate enough to have (just) enough space for such an antenna, I didn’t have the time to build it – so off to the Internet and looking at what I might be able to do given all the restraints I had.

In the end I came up with a 2 Element Vertical Beam – that took me many iterations in 4nec2 to come up with something that met my objectives and was actually a reasonable match as well.

Now this does not look like a “conventional” beam, given the reflector is 3 segments and not the usual 2. and it is a very “odd” looking shape – but hey, this will become clearer as I explain a bit more.

Notice anything nice about this radiation pattern – again 90deg on the circle is North.

Not only have I got a nice wide (about 200 degrees) beamwith, pointing in the desired direction (mostly)but there is nothing wasted out the back, and look at  the vertical pattern is – an awesome DX Antenna.  and with 7.6dBi gain, yet still enough for the up for the close NVIS/single hop contacts.

Not only did I get the desired pattern, it is a pretty darn good match!

Now the reason for the “odd configuration”  Simple, the 12M squid pole supporting the reflector and the top of the driven element is mounted at 7 Metres high on top of a shed,  and I needed to have the reflector split to go each side of the shed.   Nothing more than adapting a design and working it into the environmental’s and space you have available.

Make no mistakes, this is a BIG antenna – the top of the 12M Spiderbeam pole that is supporting the antenna is up at about 19M high and dwarfs the 2M antenna on the adjacent pole.  the photo is taken lookup up along 1 of the reflector elements.

So this antenna was erected a couple of month’s ago and wow –  does it perform!  Very impressed with the results before the OCDX – and the real-world usage indicated that the modelling was in fact very close to the results.

The Low Bands

I spent a lot of time researching as to what sort of antenna’s I could use on the low bands that were going to be achievable in the 4 weeks I had left and eventually settled on a 160M Horizontal loop for a few reasons – mainly because after reading and modelling a lot of different options, this was the antenna I could use and it met (most of) my design objectives.  It is also one of the few antenna’s that the relative performance is much better than a Dipole at low heights – as a 160M and 80M dipole at the 9M height i could achieve with this loop was no better than the random wire I used in 2017.

I did model a few that I would love to build that are in fact much better than a horizontal loop, but ran out of real estate to install it.  Co-incidentally, it was also a very good option for being so close to the ground on the low bands.

The loop was modeled, then the model was re-worked once it was installed to reflect what was actually installed.  I ended up feeding the loop with 300 ohm Ribbon cable, with a short Coax from Radio to a 1:4 balun.   Whilst it is not a perfect match, the Tuner was easily able to achieve a decent match on both 160 and 80, and the analyzer gave me a good indication that It is in fact resonant where I needed it on these 2 bands.

Now while this pattern might not seem like it is a big improvement over the 2017 one – it actually is  a massive improvement.  Yes, it is a lot of straight up, but it is 1.4dBi gain – or a 6db improvement over the previous year – and where every watt counts…

Again, at first glance, 80M doesn’t look to be brilliant, but then again – a big step up from the previous year with around a 3db improvement.  The nothing straight up was not really a hindrance to how it performed and it was remarkably good.

The Higher Bands

For 20M this year, I opted for a Full wavelength dipole  with the 3/4 w/l leg pointed at around 120 Degrees.  this antenna provides a broad “beam” with around 5db forward gain along the longer segment at reasonably low radiation angle and a bit of F/B. – Again, not the “perfect” antenna, but proved to be better than the previous year.

Given that 20M is literally  the POWER band I was simply hoping to grab a handful of multipliers here and If I worked 10 I would be happy.  I did miss out on a Short Path EU opening because I had the antenna fixed in a single direction and if I had anther antenna or been able to quickly re-orient this one may have picked up a few more contacts.

I used the 40M antenna on 15 as well – and yeah, some more effort needs to go into the modelling of the antenna to see if the 15M could be improved without degrading the primary band, or of course build a better 15M antenna – something for next year.

This year, the gap vertical was again used  but mainly for RX, with exactly 2 contacts on it – 1 on 40M to VK7 where I am at a slight disadvantage on the Beam and 1 on 10M.

Honestly, I did not put much effort into the high bands (15 and 10) given the band conditions and unlikely chance of a decent opening on these bands.

The Results

Well the proof of the modelling and antenna effort was well and truly rewarded.

This year, the conditions were nothing short of horrid yet I was able to nearly triple my score and my submitted score  this year is 29,068

The bottom line  is and, what I hope is the take-away after reading this post is Antenna’s matter – and if you take the time, model what you have you can (generally) work out how to do something better than what you may already have in place.

Final word – I enter QRP not because it is easy, but because it is hard!

VK5 is of course also at an added disadvantage – given that we are 1 hop further away than the other states – and over land and not water, further compounding the need to maximize our Antenna efforts.

I missed out on a heck of a lot of potential contacts because in am 20+ dB down with my power, but I had a blast actually doing what I did.

Update 12/10

I forgot to mention and now adding it in here.

One of the issues I had last year was my callsign – VK5FO – Whilst it has a certain charm and schoolyard smut factor, it was actually a problem during contests.  I spent a fair bit of time, listening to the bands, listening to callsigns and then went and looked at available callsigns.

I applied for and was Granted VK5HC (Hotel Charlie,  Henry Charlie, Honolulu California, or my favourite – welcome to the Hotel California) and yes, the callsign makes a difference when you are (I am) on the RX stations noise-floor). The callsign choice probably helped me actually complete 5 to 10% of the very difficult contacts.

A “contest callsign” that is phonetically easy is a worthwhile addition

This year,  for something a bit different the FD was never about building a full-on 4 band station and going all out for a big score – it was all about doing more with less.

We (Me, Bob VK5FO and Ray VK5RR) teamed up with Andy, VK5AKH and went QRP portable and went for a “nice” hike up to Black Hill Summit – a summit that is a hike in – and at 460M above sea level in PF95ic

We met down the bottom of the hill about an hour before the start and packed up the gear and antennas and away we went

We were taking gear to get us on the air on 4 bands for field day – 6m, 2m, 70cm and 23cm.

After nearly an hour, we finally made it to the summit at around 01:10 UTC just after the start time and proceeded to set up Antennas and Radio’s

Here you can see the Antenna’s – 1/2 Wave Vertical for 6m on the blue pole, and on the Camera Tripod, you can see the 11 Ele on 23cm, the 6 Ele on 70cm and the Slim Jim for 2m.

Andy making a contact on 6m with the KX3.

The summit, while it doesn’t offer great views has shade! which makes for a pleasant place to operate from.

Did I say minimal station set-up.  Here I am with the KX3 and you can see the 70cm XVTR and batteries in the foreground.

We were set up pretty much at the old trig point – I say old, because someone has ripped it all out of the ground at some point and built a pile of rocks adjacent to it on the walking trail.

The aim of the day was to enjoy the hike up to the top of the hill and play a bit of radio and within an hour or so we had contacts on all 4 bands.  It was all about getting out for a few hours, and getting a few contacts and handing out contacts to the other stations who were also out and about.

As far as FD goes, it is a decent location for a minimal set-up basic antenna’s that we carried in, and very modest power  on all bands – we had 5w on 6m, 2m and 70cm and 3w on 23cm.  It truly is a case of “height is might” when it comes to VHF/UHF and above.

Mid-afternoon we packed up and headed back down the trail.

It doesn’t look it, but it was a decent hike – with about 2km each way and 250+M elevation change.  Coming back down was a bit quicker it was only about 40 minutes. Here we were about 5 minutes from the bottom.

We had APRS running on the Handheld while hiking in and out.

At the end of the day, I logged 16 contacts for FD, and Andy logged 21, in the 3 hours or so we were at the Summit.

As we were operating from Black Hill, this also qualified as both a SANPCPA and VKFF Activation.